• Conveyor belt
  Multiply NN & EP Carcass

• Power Transmission Belt
  For Industrial, Automotive, etc.
  Wrapped, raw Edge Type, etc

• Other Products
  Rubber Sheet
  Rubber Hose
  Hair Belts
  Hair Balts
  Cotton Belts
  Textile Transmission Belts

• kapurthala range of Coneyor Belts covers a wide spectrum of types & application .The spectrum covers:

Width

upto 1600mm

Edges

Cut & Moulded

Length

Open & Endless

Ply Construction

Straight Ply, Stepped Ply,

Plies

2 to 12

Reverse Ply

• Fabric

Cotton/Nylon

CN 40,50,60

Nylon/Nylon

N6 & N66

Cotton/Cotton

28oz, 32oz, 36oz & 42oz

Synthetic Fabric

Polyester Polyamide (EP)

 Conveyor belt generally consists of cover rubber, carcass and rubber skim coat. The reinforced breaker fabric is used for extra protection

• COVER RUBBER
  Covers of natural or synthetic rubber are designed to protect the carcass from -abrasion, impact, deterioration and other injurious influences. They are compounded to meet particular service conditions such as abrasion, oil, heat, fire, chemical resistant and antistatic, etc.

• CARCASS
  Carcass of a belt maintains the belt tension and supplies structural strength; it does all of the work in supporting and pulling the load. Carcass consists of multiple pl1es of rubber impregnated fabric bonded with friction and skim coats. The fabrics most commonly used are;' nylon, polyester and cotton, etc.

• RUBBER SKIM COAT
   An extra layer compound between plies that increases flex life and creates a more elastic link so that plies flex without separation. Skim coats cushion fabrics against impact and help protect against moisture.

• RUBBER SKIM COAT
  An extra layer compound between plies that increases flex life and creates a more elastic. link so that plies flex without separation. Skim coats cushion fabrics against impact and help protect against moisture.

• BREAKER FABRIC
  A specially woven fabric between' the cover and the carcass to improve adhesion and provide better resistance to cover stripping, gouging or tearing. This is normally used in belts handling primarily crushed and sized material which gives great impact to the belt when lumps drop at a loading point.

• COMPOUND AND USAGE
  The cover rubber determines belt life and the selection of the correct cover rubber grade and thickness is most important.

• HEAT RESISTANT CONVEYOR BELT
  In general, it is economical to adopt a heat resistant belt if the temperature of the material to be carried is over 60 C (1 400 F). As the damage of cover depends on the temperature and nature of transported material, the proper selection of a belt to fit particular operating conditions is important. Especially the relation of temperature between the material and belt surface should be considered when selecting the belt.
  
  When transporting material of high temperature of belt surface rises by contact with the material, but on the return journey the heated surface gets cooled naturally by air so that the surface temperature becomes considerably cooler than that of the material. The temperature depends on kind, size, temperature quantity of material to be carried, belt speed, belt length and etc. This belt is designed for transporting cement clinker, cokes, sintered ores, soda ash, chemicals, fertilizer and etc.

• ABRASION RESISTANT CONVEYOR BELT
  Material being carried as well as idlers and frame of the conveyor may cause excessive wearing on normal bells. To prolong the life of the belts running under severe wearing conditions, special and super abrasion rubber is compounded for the belt covers.

• OIL RESISTANT CONVEYOR BELT
  Oily material causes the ordinary rubber covers of the belt to swell and peel off, which results in a complete breakdown in the conveyor system. This belt compounded of oil-resistant -quality synthetic rubber has good resistance to the damaging effects encountered when conveying oil.

• FIRE RESISTANT CONVEYOR BELT
  This belt is a prerequisite to prevent fire risks in coal mines where not easily accessible and to reduce maintenance of the conveyors which may be damaged by flame at the blast furnaces of iron works.

• FOOD CONVEYOR BELT
  This belt is made for use where foodstuffs are handled. The covers are compounded to provide nontoxic, tasteless and odourless properties.

• ANTI-STATIC CONVEYOR BELT
  This belt is made especially for use where, for instance in the paper or textile mills, the products being carried stick to the belt surface, or fire risks may be involved due to electro-static sparks.